1. The self-priming pump should be placed in a well-ventilated place as much as possible to facilitate rapid heat dissipation and reduce motor temperature. Otherwise, long-term operation can easily burn the motor. For example, when a farmer uses a self-priming pump, it does not remove the plastic film covering the motor, causing the motor to overheat and burn out the coil. In addition, before starting, be sure to check the amount of water in the pump body, otherwise, not only affect the self-priming performance, but also easy to burn the shaft seal components. Under normal conditions, the water should be discharged within 3 to 5 minutes after the pump is started. Otherwise, it should be stopped immediately.
2. Before starting the submersible pump, some necessary inspections should be done: whether the rotation of the pump shaft is normal, whether there is a stuck phenomenon, whether the position of the impeller is normal, and whether the cable and the cable plug have cracks, scratches, and breakage. Pay attention to observe the change of voltage during operation, generally control within ± 5% of rated voltage. In addition, the location of the pump in the water is very important. It should be possible to choose a place where there is plenty of water, no silt, and good water quality. It should be suspended vertically in the water. It must not be placed horizontally so as to avoid being trapped in the mud or blocked by the suspended material. Lead to a sharp drop in the amount of water or even no access to water.
3. Pump maintenance When the pump fails, do not remove it yourself. Because of their own demolition, first, they do not know where the fault caused blindly dismantling a pass; Second, there is no special tools and often damage the original spare parts. The best way is to go to an experienced and large-scale maintenance point repair and replace “overage†parts and certain wearing parts in time. Under normal circumstances, the pump should be repaired every six months to eliminate "disease" work.
4. Non-use period is stored in the non-use period, the water pump should be lifted off the water source in time, and the water in the pump should be drained, especially in the cold winter. Then place it in a dry place. Conditional users can also apply grease to the key parts of the pump and add lubricant to the bearings to prevent corrosion of the parts. In addition, the non-use period of the pump is not as long as possible. If you do not use it for a long time, it will not only easily rust parts, but also reduce the service life of the pump.
2. Before starting the submersible pump, some necessary inspections should be done: whether the rotation of the pump shaft is normal, whether there is a stuck phenomenon, whether the position of the impeller is normal, and whether the cable and the cable plug have cracks, scratches, and breakage. Pay attention to observe the change of voltage during operation, generally control within ± 5% of rated voltage. In addition, the location of the pump in the water is very important. It should be possible to choose a place where there is plenty of water, no silt, and good water quality. It should be suspended vertically in the water. It must not be placed horizontally so as to avoid being trapped in the mud or blocked by the suspended material. Lead to a sharp drop in the amount of water or even no access to water.
3. Pump maintenance When the pump fails, do not remove it yourself. Because of their own demolition, first, they do not know where the fault caused blindly dismantling a pass; Second, there is no special tools and often damage the original spare parts. The best way is to go to an experienced and large-scale maintenance point repair and replace “overage†parts and certain wearing parts in time. Under normal circumstances, the pump should be repaired every six months to eliminate "disease" work.
4. Non-use period is stored in the non-use period, the water pump should be lifted off the water source in time, and the water in the pump should be drained, especially in the cold winter. Then place it in a dry place. Conditional users can also apply grease to the key parts of the pump and add lubricant to the bearings to prevent corrosion of the parts. In addition, the non-use period of the pump is not as long as possible. If you do not use it for a long time, it will not only easily rust parts, but also reduce the service life of the pump.
Benefits For Your Influencer Kit Packaging Boxes
Order our Influencer Kit Packaging boxes at wholesale rates when placing an order in bulk.
Customization coming in any size to fit different ends.
Made of heavyweight chipboard to build strong construction for any end.
Print any color of custom logo and full color photographic custom design.
Print finishes like hot stamping, embossing, deboss are available to print.
Influencer Kits Box,Influencer Kit Packaging,Influencer Kit Bespoke Box,Influencer Kit Box Packaging
UCPACK , https://www.packpioneers.com