3 Year for motor and controller. Solar panel 20 years(Optional)
Â
Installation
 1. Wiring the pump
 Connecting a longer cable to the pump,(size of cable must be at least 1.5mm²)
Use the parts contained in the cable connector kit( heat-shrink tube and tape) to connect a longer supply wire to the pump. If you don't have a heat gun to shrink the tube, the barrel of your soldering iron will do or you can use a butane torch but with great care so you don't melt the insulation or set it on fire. Bare the insulation back as shown above.
A. Layout the components needed to make the joinÂ
B. Put the large diameter piece of heat-shrink over the main cable and then the smaller diameter pieces over the individual wires, keep the heat-shrink back away from the joints as you solder them. Any heat transfer will prematurely shrink the heat-shrink.
C.  Slide the small heat-shrink over the soldered joints and heat using a heat gun or alternative heat source to shrink the sleeve down over the wires.
D. Wrap the tape over the sealed joints
E. Finally slide the large diameter heat-shrink over the completed joint and shrink to it.
Place the pump in water before you start wiring the controller box this will allow the pump to go through the pre-conditioning required. Do not put the pump in its final position until you have tested it, unless it is easy to see and remove.
Â
- Solar pump control box
  B. over-current protection( it is automatic)
  C. protection for low water level in well( A B sensor)
  D. protection for full water level in tank( L H sensor)
  E. Controlling running speed of motor( speed regulator)
  F. Delay working when full water in tank( a timer inside can delay working for 30 seconds when the tank going to not full)
  G. MPPT function.(maximum power point tracking)
  H. Battery is optional.( battery can be used with solar charger battery system)
 Warranty:
3 Year for motor and controller. Solar panel 20 years(Optional)
Â
Installation
 1. Wiring the pump
 Connecting a longer cable to the pump,(size of cable must be at least 1.5mm²)
Use the parts contained in the cable connector kit( heat-shrink tube and tape) to connect a longer supply wire to the pump. If you don't have a heat gun to shrink the tube, the barrel of your soldering iron will do or you can use a butane torch but with great care so you don't melt the insulation or set it on fire. Bare the insulation back as shown above.
A. Layout the components needed to make the joinÂ
B. Put the large diameter piece of heat-shrink over the main cable and then the smaller diameter pieces over the individual wires, keep the heat-shrink back away from the joints as you solder them. Any heat transfer will prematurely shrink the heat-shrink.
C.  Slide the small heat-shrink over the soldered joints and heat using a heat gun or alternative heat source to shrink the sleeve down over the wires.
D. Wrap the tape over the sealed joints
E. Finally slide the large diameter heat-shrink over the completed joint and shrink to it.
Place the pump in water before you start wiring the controller box this will allow the pump to go through the pre-conditioning required. Do not put the pump in its final position until you have tested it, unless it is easy to see and remove.
Â
- Solar pump control box
  B. over-current protection( it is automatic)
  C. protection for low water level in well( A B sensor)
  D. protection for full water level in tank( L H sensor)
  E. Controlling running speed of motor( speed regulator)
  F. Delay working when full water in tank( a timer inside can delay working for 30 seconds when the tank going to not full)
  G. MPPT function.(maximum power point tracking)
  H. Battery is optional.( battery can be used with solar charger battery system)
Â
CONNECT have the best way to get money from waste for beef, sheep, hogs and poultry meat, the further processing is becoming more important especially the use of biproducts. For animals ,poultry farms and slaughterhouses, large amount of dead animals and wastes are lost, or burn it with fire, so not profit just waste, with our rendering equipment we change wast to money also no environmental pollution. CONNECT Rendering Equipment latest technology , turn these waste into profit, the all our machines environmental friendly system, odourless toair. bone mill, blood meal, viscera or meat meal , Feather Meal can be added to feed as the Protein Meal . , fat, ash, and digestible protein and, can be directly add to feed meal
Connect rendering Industries is a high technology process, providing best solutions for the benefit of the environment. We can supply complete systems and equipment for the processing of animal by-products, waste, sewage sludge waste and by-products from food and beverage production
Connect rendering machinery and equipment offers the protein recycling industry of rendering systems
also can recycle red meat, poultry and fish by-products into profitable meals and fats
with big range of process applications, including systems y for oil seed extraction, process drying, food waste, paper dewatering, distiller`s dried grain reclamation
CONNECT protein Rendering Plant manufacture is the solution for waste animal slaughterhouse, poultry slaughterhouse, animal and chicken farms` wastes. connect equipment including the raw material collecting, cooking, drying, oil pressing, cooling, packing and odor processing. The capacity start from 1Ton/Batch rendering capacity to each day 150 Ton wastes. Our successful stories projects is in more than 25 countries in the world, in latin America,middle east,,Africa,,north America , Russian and asia countries.
Connect have variety of designs for clients to meet the requirement of different production ,investment, t. Our products is accepted by many clients by its high standard quality and competitive price.come to check and decide, connect with us if you want to earn money from waste
Rendering Equipment
Rendering Equipment, Animal Rendering Plant, Poultry Rendering Plants, Chicken Rendering Plant,Rendering Plant
Connect Group For Poultry Project , https://www.connectpoultry.com